Analysis of the Physical Boundary Conditions for the Layout of an Optimized Ethanol Low-Temperature Mixture Preparation Devices.

Analysis of the Physical Boundary Conditions for the Layout of an Optimized Ethanol Low-Temperature Mixture Preparation Devices.

Author(s):

Publication title:

2009 SAE world congress : technical paper

Title of ser.:

Society of Automotive Engineers technical paper series

Ser. no.:

2009

Pub. Year:

2009

No.:

2009-01-0618

Paper no.:

2009-01-0618

Pages:

13

Pub. info.:

Warrendale, Penn.: Society of Automotive Engineers

ISSN:

01487191

Language:

English

Call no.:

S10400

Type:

Technical Paper

Details

TDL ID:	ZA00052095
Series ID:	PA00000058
Conf. info. (Name):	SAE World Congress & Exhibition, 2009
Conf. info. (Number):	2009
Conf. info. (Venue):	Detroit, MI, USA
Conf. info. (Date):	2009.04.20-2009.04.23
Note for article:	SAE 2009 World Congress, April 20-23, 2009, Detroit, Michigan, USA

Similar Items:

1 Technical Paper Analysis of the Capabilities of the New Innovative Ethanol Low-Temperature Mixture Preparation Device ECS. Pontoppidan, M., Bonfiglioli, S., Montanari, G. Society of Automotive Engineers	7 Technical Paper Introduction of Virtual Spray Vessel (VSV) simulation approach to improve the optimization level of mass-produced 3rd generation fuel injectors for SFS-Flex … Pontoppidan, M., Montanari, G. Society of Automotive Engineers
2 Technical Paper Description of Preliminary Study for Technology Transfer of an Ethanol Mixture Preparation System from Automotive Application to a 4-Cylinder 5.9 liter Aircraft … Pontoppidan, M., Bonfiglioli, S., Montanari, G., Damasceno, F., Bucci, A. Society of Automotive Engineers	8 Technical Paper Detailed Study on Ethanol In-Cylinder Combustion Behavior by Means of a Numerical Virtual Engine Model Approach. Pontopiddan, M., Damasceno, C.F., Montanari, G., Bonfiglioli, S. Society of Automotive Engineers
3 Technical Paper The Integral Flex-Vehicle Mixture Control of Alcohol-Based Bio-Fuels - A New Challenge for Fuel-Atomizer Optimization. Pontoppidan, M., Damasceno, F. Society of Automotive Engineers	9 Technical Paper Parametric Study of Physical Requirements for Optimization of the EGR-rate and the Spray Formation for Minimum Emissions Production Over a Broad Range of … Pontoppidan, M., Demaio, A., Bella, G., Rotondi, R. Society of Automotive Engineers
4 Technical Paper New Developments in Fuel Injector Atomizer Layouts for Port Fuel Injection Applications to Meet PL6 and ULEV Requirements. Pontoppidan, M., Montanari, G. Society of Automotive Engineers	10 Technical Paper New Innovative Simulation Tool, the Virtual Spray Vessel (VSV), to Improve the Characterization and Spray Stability of Mass Produced Fuel Injectors. Pontoppidan, M., Montanari, G. Society of Automotive Engineers
5 Technical Paper Development of a New Innovative Software-Based Sensing Technique to Instantaneously Measure the Mixture Fraction of Bio-Diesel Present in a Crude Oil Based … Montanari, G., Pontoppidan, M. Society of Automotive Engineers	11 Technical Paper The Development of the DL Fuel Injector Atomizer with Active Droplet Coalescence Control for Port Fuel Injection Applications. Pontoppidan, M., Montanari, G. Society of Automotive Engineers
6 Technical Paper Development of a New In-Vehicle Sensing Method to Instantaneously Measure the Mixture Fraction of Bio-Diesel Present in a Crude Oil Based Classic Diesel Fuel. Pontoppidan, M., Montanari, G. Society of Automotive Engineers	12 Technical Paper Analysis of mixture preparation quality versus the use of different types of passively air-assisted fuel port injectors Pontoppidan,M., Cristiani,M. Society of Automotive Engineering, Inc.

1

2

3

4

5

6

7

8

9

10

11

12