Engineering Design with Injection-Molded Thermoplastics

Engineering Design with Injection-Molded Thermoplastics

Author(s):

Trantina, G. G. ( General Electric Corporate Research and Development )
Wyzgoski, M. G. ( General Motors Corporate Research and Development )

Publication title:

ANTEC 94 : plastics : gateway to the future : conference proceedings, San Francisco May 1-5 1994 : Volume III. Special areas

Title of ser.:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

Ser. no.:

40(3)

Pub. Year:

1994

Vol.:

3

Page(from):

3159

Page(to):

3165

Pages:

7

Pub. info.:

Brookfield, CT: Society of Plastics Engineers, Inc. (SPE)

Language:

English

Call no.:

S42700/941470

Type:

Conference Proceedings

Details

TDL ID:	ZA00019689
Series ID:	PA00000030
Conf. info. (Name):	ANTEC '94 : Annual Technical Conference
Conf. info. (Number):	52nd
Conf. info. (Venue):	San Francisco, CA, USA
Conf. info. (Date):	1994.05.01-1994.05.05
Note for article:	PRODUCT DESIGN & DEVELOPMENT DIVISION-IN-FORMATION

Similar Items:

1 Conference Proceedings Structural Failure Prediction with Short-Fiber Filled, Injection Molded Thermoplastics Ambur, G., Trantina, G. Society of Plastics Engineers, Inc. (SPE)	7 Conference Proceedings The Effect of Nonlinear Material Behavior on Snap-Fit Design Trantina, G. G., Minichelli, M. D. Society of Plastics Engineers, Inc. (SPE)
2 Conference Proceedings Anisotropic Properties of Injection-Molded Short-Fiber Thermoplastics Liang, E. W., Trantina, G. G. Society of Plastics Engineers, Inc. (SPE)	8 Conference Proceedings Residual Stresses in Injection Molded Thermoplastics Vincent, M., Giroud, T. Trans Tech Publications
3 Conference Proceedings An Engineering Design System for Thermoplastics Trantina G. G., Ysseldyke A. D. Society of Plastics Engineers, Inc. (SPE)	9 Conference Proceedings Heat Transfer Measurement at the Mold Surface During Injection Molding of Thermoplastic Melts Kamal, M. R., Salloum, G., Garcia-Rejon, A. Society of Plastics Engineers, Inc. (SPE)
4 Conference Proceedings Mechanical Properties of Long-Fiber Filled Injection-Molded Thermoplastic Composites Stokes, V. K., Inzinna, L. P., Trantina, G. G., Liang, E. W., Woods, J. T. Society of Plastics Engineers, Inc. (SPE)	10 Conference Proceedings Use of deformation maps in predicting the time-dependent deformation of thermoplastics Hasan, Omar A., Trantina, Gerald G. Society of Plastics Engineers, Inc. (SPE)
5 Conference Proceedings Reinforced Plastic Design: Tensile versus Flexural Fatigue Krohn, J. A., Novak, G. E., Wyzgoski, M. G. Society of Plastics Engineers	11 Conference Proceedings Development of an ISO Standard for Determining Anisotropic Properties of Glass-Filled Thermoplastics O'Gara, J.F., Wyzgoski, M.G., Novak, G.E. Society of Plastics Engineers
6 Conference Proceedings Injection Molded Engineering Thermoplastics: A Critical Evaluation of Processability and Part Dimensional Stability Efner, H., Largent, T., Allen, D., Lee, D. M. Society of Plastics Engineers, Inc. (SPE)	12 Conference Proceedings Material properties for part design and material selection Trantina, Gerald G. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12