Blank Cover Image

Novel Reaction Injection Moulding Processing of Polyurethanes: In Shot Ratio Variation and Twin Mixhead Injection

Author(s):
Publication title:
ANTEC 94 : plastics : gateway to the future : conference proceedings, San Francisco May 1-5 1994 : Volume II. Materials
Title of ser.:
Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers
Ser. no.:
40(2)
Pub. Year:
1994
Vol.:
2
Page(from):
1654
Page(to):
1658
Pages:
5
Pub. info.:
Brookfield, CT: Society of Plastics Engineers, Inc. (SPE)
Language:
English
Call no.:
S42700/941469
Type:
Conference Proceedings

Similar Items:

1 Conference Proceedings Injection Moulding: Intelligent Process Monitoring to Discriminate Material and Process Variations

Khoshooee N., Dawson J. A., Key A., Coates D. P., Kumar S.

Society of Plastics Engineers, Inc. (SPE)
7 Conference Proceedings Injection Moulding In-Process Measurements of Batch to Batch Variation and Process Variable Influences in Polyamides

Cotes, P. D., Kelly, A. L., Woodhead, M., Dawson, A. J., Martyn, M., Khoshooee, N.

Society of Plastics Engineers, Inc. (SPE)
2 Conference Proceedings Development of a Novel Reaction Injection Moulding Process for Syndiotactic Polystyrene

Shan P. L. C., Baker E. W., Cunningham F. M., Baird C. M.

Society of Plastics Engineers, Inc. (SPE)
8 Conference Proceedings Modelling of the Effects of Mould Venting on the Injection Moulding Process

Gao M. D., Reymond S., Hetu F. J., Garcia-Rejon A.

Society of Plastics Engineers, Inc. (SPE)
3 Conference Proceedings Organic Fibre Reinforced Polymer Matrix Composites Produced by SRIM

Coates, P. D., Long, S. D., Johnson, A. F., Tucker, N., Wong, S.

Society of Plastics Engineers, Inc. (SPE)
9 Conference Proceedings Injection Moulding Process Assessment by Energy Monitoring

Dawson, A., Coates, H.S.Rajamani; P., Collis, R., Owen, L., Owen, D.

Society of Plastics Engineers
4 Conference Proceedings Setup and Optimisation of the Gas Assisted Injection Moulding Process Using an Expert System

Coates, P.D., Mulvaney-Johnson, L., Speight, R.G., Brincat P., Bakharev, A.S.

Society of Plastics Engineers
10 Conference Proceedings Ultrasonic Monitoring of Gas Assisted Injection Moulding (GAIM)

Brown, E.C., Mulvaney-Johnson, L., Coates, P.D.

Society of Plastics Engineers
5 Conference Proceedings Injection Moulding Process Studies for Polyketones

Martyn T. M., Coates D. P., Bonner G. J., Davidson N.

Society of Plastics Engineers, Inc. (SPE)
11 Conference Proceedings Experimental Study of Simultaneous Co-Injection Moulding Process

Somnuk P., Smith F. G.

Society of Plastics Engineers, Inc. (SPE)
6 Conference Proceedings Fluid Assisted Polymer Processing in Extrusion and Injection Moulding: A Comparative Overview

Mulvaney-Johnson, L., Woodhead, M., Rose, M., Dawson, A., Gough, T.D., Coates, P.D., Smith, G.F., Goodship, V., …

Society of Plastics Engineers
12 Conference Proceedings Comparison of Injection Moulding Simulation and In-Process Measurements

Leman Z., Coates D. P.

Society of Plastics Engineers, Inc. (SPE)
1
 
2
 
3
 
4
 
5
 
6
 
7
 
8
 
9
 
10
 
11
 
12